Muddy Boots, Inc.

Home
   

Privacy Policy

About Us






Von Morris

<< Previous Page Next Page >>




Von Morris Cabinet Hardware 1.5&quot; x 1.5&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-1515 (SKU: KnobsandThings 37505)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :1.5&quot; Width Open : 1.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 6 x 0.75&quot; Screw Quan. Per Hinge: 8 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 2.0&quot; x 1.5&quot; Cabinet Hinge - Solid Brass - Olive Knuckle - 19-2015 (SKU: KnobsandThings 31046)
Von Morris Cabinet Hardware Von Morris Cabinet Olive Knuckle Hinge Solid Brass - Olive Knuckle -Cabinet Hinge Length of Joint :2.0&quot; Width Open : 1.5&quot; Gauge of Metal : 0.0935&quot; Screw Size : 6 x 0.75&quot; Screw Quan. Per Hinge: 6 Knuckle Size : 1.12&quot;H x 0.39&quot;D Olive Knuckle Hinges are Priced and Sold as Eaches Hinges Number 19-2015 and 19-2520 are equipped with one brass bushing each. Hinge 19-3025 is equipped with one precision machined ball bearing assembly Ball bearings are machined from 300 series Stainless Steel and employ Stainless Steel balls. All pins are precision machined from 300 series Stainless Steel. All olive knuckle hinges are handed. Be sure to specify hand of hinge when ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS - OLIVE KNUCKLE - CABINET HINGE HINGE BODY: Hinge body is manufactured of solid forged brass. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are Stainless Steel as well. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 300 Stainless Steel for high durability and resistance to rust. They are permanently installed in one half of the hinge. The other end is rounded to facilitate re-assembly. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged 6 per bag to facilitate sales of half pairs. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE PIN COVER SELECTION


Von Morris Cabinet Hardware 2.0&quot; x 1.5&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-2015 (SKU: KnobsandThings 33072)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :2.0&quot; Width Open : 1.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 6 x 0.75&quot; Screw Quan. Per Hinge: 12 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 2.5&quot; x 1.7&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-2517 (SKU: KnobsandThings 33235)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :2.5&quot; Width Open : 1.7&quot; Gauge of Metal : 0.093&quot; Screw Size : 6 x 0.75&quot; Screw Quan. Per Hinge: 12 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 2.5&quot; x 2.0&quot; Cabinet Hinge - Solid Brass - Olive Knuckle - 19-2520 (SKU: KnobsandThings 36401)
Von Morris Cabinet Hardware Von Morris Cabinet Olive Knuckle Hinge Solid Brass - Olive Knuckle -Cabinet Hinge Length of Joint :2.5&quot; Width Open : 2.0&quot; Gauge of Metal : 0.0935&quot; Screw Size : 14 x 0.75&quot; Screw Quan. Per Hinge: 6 Knuckle Size : 1.49&quot;H x 0.50&quot;D Olive Knuckle Hinges are Priced and Sold as Eaches Hinges Number 19-2015 and 19-2520 are equipped with one brass bushing each. Hinge 19-3025 is equipped with one precision machined ball bearing assembly Ball bearings are machined from 300 series Stainless Steel and employ Stainless Steel balls. All pins are precision machined from 300 series Stainless Steel. All olive knuckle hinges are handed. Be sure to specify hand of hinge when ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS - OLIVE KNUCKLE - CABINET HINGE HINGE BODY: Hinge body is manufactured of solid forged brass. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are Stainless Steel as well. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 300 Stainless Steel for high durability and resistance to rust. They are permanently installed in one half of the hinge. The other end is rounded to facilitate re-assembly. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged 6 per bag to facilitate sales of half pairs. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE PIN COVER SELECTION


Von Morris Cabinet Hardware 2.5&quot; x 2.0&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-2520 (SKU: KnobsandThings 36555)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :2.5&quot; Width Open : 2.0&quot; Gauge of Metal : 0.093&quot; Screw Size : 6 x 0.75&quot; Screw Quan. Per Hinge: 12 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 2.5&quot; x 2.5&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-2525 (SKU: KnobsandThings 37458)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :2.5&quot; Width Open : 2.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 8 x 0.75&quot; Screw Quan. Per Hinge: 12 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 3.0&quot; x 2.0&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-3020 (SKU: KnobsandThings 37465)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :3.0&quot; Width Open : 2.0&quot; Gauge of Metal : 0.125&quot; Screw Size : 8 x 0.75&quot; Screw Quan. Per Hinge: 12 USE FINIALS 60-FF-L OR 60-UF-L. ALL OTHERS USE EITHER 60-FF OR 60-UF. All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware 3.0&quot; x 2.5&quot; Cabinet Hinge - Solid Brass - Olive Knuckle - 19-3025 (SKU: KnobsandThings 37463)
Von Morris Cabinet Hardware Von Morris Cabinet Olive Knuckle Hinge Solid Brass - Olive Knuckle -Cabinet Hinge Length of Joint :3.0&quot; Width Open : 2.5&quot; Gauge of Metal : 0.0935&quot; Screw Size : 14 x 1.00&quot; Screw Quan. Per Hinge: 6 Knuckle Size : 1.62&quot;H x 0.50&quot;D Olive Knuckle Hinges are Priced and Sold as Eaches Hinges Number 19-2015 and 19-2520 are equipped with one brass bushing each. Hinge 19-3025 is equipped with one precision machined ball bearing assembly Ball bearings are machined from 300 series Stainless Steel and employ Stainless Steel balls. All pins are precision machined from 300 series Stainless Steel. All olive knuckle hinges are handed. Be sure to specify hand of hinge when ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS - OLIVE KNUCKLE - CABINET HINGE HINGE BODY: Hinge body is manufactured of solid forged brass. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are Stainless Steel as well. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 300 Stainless Steel for high durability and resistance to rust. They are permanently installed in one half of the hinge. The other end is rounded to facilitate re-assembly. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged 6 per bag to facilitate sales of half pairs. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE PIN COVER SELECTION


Von Morris Cabinet Hardware 3.5&quot; x 2.5&quot; Cabinet Hinge - Solid Extrude Brass - Loose Pin - 60-3025 (SKU: KnobsandThings 37462)
Von Morris Cabinet Hardware Von Morris Cabinet Hinge - Solid Extrude Brass - Loose Pin Cabinet Hinge - Solid Extrude Brass - Loose Pin Length of Joint :3.5&quot; Width Open : 2.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 8 x 0.75&quot; Screw Quan. Per Hinge: 12 All hinges are packed with solid brass type &quot;A&quot; tapping flathead screws of the appropriate size. Brass Cabinet Hinges are supplied with threaded Decorative Ball Finials. Other finials are available at additional cost. All finials are threaded into the barrel of the hinge to prevent the pin from rising. All finials are sized to match the diameter of the hinge barrels to which they are mounted. Sold as Pairs FEATURES OF: SOLID EXTRUDE BRASS - LOOSE PIN - CABINET HINGE HINGE BODY:Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 series Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FASTENERS:All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either four per bag or six per bag to facilitate sales of half pairs. FINIALS: Cabinet hinges come with threaded ball finials installed. Other finials are available, packed in sets of four. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR HINGE FINIAL SELECTION


Von Morris Cabinet Hardware Acorn Solid Brass Mortise Hinge Finials - 11-AF (SKU: KnobsandThings 37461)
Von Morris Cabinet Hardware Von Morris Solid Brass Mortise Hinge Finials Set of 4 Acorn Finials All finials are interchangeable with all full mortise hinge sizes. ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Cabinet Hardware Cabinet Solid Brass Olive Knuckle Pin Cover - 19-3000 (SKU: KnobsandThings 31047)
Von Morris Cabinet Hardware Von Morris Solid Brass Olive Knuckle Pin Cover Olive Knuckle Pin Cover, Each For Item 19-2015, 19-2520, and 19-3025 ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Cabinet Hardware Flat Solid Brass Mortise Cabinet Hinge Finials - 60-FF (SKU: KnobsandThings 33074)
Von Morris Cabinet Hardware Von Morris Solid Brass Mortise Cabinet Hinge Finials Set of 4 Flat Finials ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Cabinet Hardware Flat Solid Brass Mortise Cabinet Hinge Finials - 60-FF-L (SKU: KnobsandThings 33236)
Von Morris Cabinet Hardware Von Morris Solid Brass Mortise Cabinet Hinge Finials Set of 4 Flat Finials For ITEM # 60-3020 ONLY ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Cabinet Hardware Urn Solid Brass Mortise Cabinet Hinge Finials - 60-UF (SKU: KnobsandThings 36404)
Von Morris Cabinet Hardware Von Morris Solid Brass Mortise Cabinet Hinge Finials Set of 4 Urn Finials ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Cabinet Hardware Urn Solid Brass Mortise Cabinet Hinge Finials - 60-UF-L (SKU: KnobsandThings 36556)
Von Morris Cabinet Hardware Von Morris Solid Brass Mortise Cabinet Hinge Finials Set of 4 Urn Finials For ITEM # 60-3020 ONLY ETERNA Life long finish The rich luster of highly polished brass has been cherished for centuries for its luxury, quality and elegant beauty. However, an inherent characteristic of brass is that without fail it will tarnish over time due to exposure to air, moisture, and ultraviolet rays. Clear coat finishes have delayed the tarnishing, but by no means stopped it. It has never been possible to offer a guarantee for a clearcoat finish. Von Morris Corporation is very pleased to introduced our new ETERNA Life long finish as the solution to this problem. ETERNA Life long finish is a proprietary blend of space age materials which is applied to Von Morris hinges in multiple layers over polished brass to produce the durability of armor plate. ETERNA Life long finish is guaranteed to the original buyer not to tarnish, pit, flake or discolor for as long as he or she owns the product. ETERNA Life long finish products are supplied with screws and accessories in matching ETERNA Life long finish ETERNA Life long finish is available on most Von Morris products. Identify it by the finish code 605E. Von Morris has now made it possible for you to enjoy the elegance and beauty of polished brass with the assurance of the permanence of its lustrous finish. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Door Hardware 3.0&quot; x 2.5&quot; Hinge - Solid Extrude Brass - Plain Bearing - Standard Weight - 11-3025 (SKU: KnobsandThings 37548)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 2.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 All 11 Series Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. #12 Machine Screws available for 11-4040 and 11-4545 upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.0&quot; x 2.5&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-3025/2 (SKU: KnobsandThings 37549)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 2.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Hinge: 6 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL OR TWO KNUCKLE HINGE PIN COVER SELECTION


Von Morris Door Hardware 3.0&quot; x 2.5&quot;Hinge - Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight - 13-3025/3 (SKU: KnobsandThings 37550)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 2.5&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.0&quot; x 3.0&quot; Hinge - Solid Extrude Brass - Plain Bearing - Standard Weight - 11-3030 (SKU: KnobsandThings 33082)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 3.0&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 All 11 Series Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. #12 Machine Screws available for 11-4040 and 11-4545 upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.0&quot; x 3.0&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-3030/2 (SKU: KnobsandThings 31028)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 3.0&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Hinge: 6 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL OR TWO KNUCKLE HINGE PIN COVER SELECTION


Von Morris Door Hardware 3.0&quot; x 3.0&quot;Hinge - Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight - 13-3030/3 (SKU: KnobsandThings 33092)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.0&quot; Width Open : 3.0&quot; Gauge of Metal : 0.093&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.5&quot; x 3.5&quot; Hinge - Solid Extrude Brass - Plain Bearing - Standard Weight - 11-3535 (SKU: KnobsandThings 33217)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Plain Bearing - Standard Weight Length of Joint : 3.5&quot; Width Open : 3.5&quot; Gauge of Metal : 0.123&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 All 11 Series Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. #12 Machine Screws available for 11-4040 and 11-4545 upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.5&quot; x 3.5&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-3535/2 (SKU: KnobsandThings 36405)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.5&quot; Width Open : 3.5&quot; Gauge of Metal : 0.123&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Hinge: 6 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL OR TWO KNUCKLE HINGE PIN COVER SELECTION


Von Morris Door Hardware 3.5&quot; x 3.5&quot; Hinge - Steel Paint Hinge - Plain Bearing - Standard Weight - 12-3535 (SKU: KnobsandThings 36539)
Von Morris Door Hardware Von Morris Steel Full Mortise Hinge Steel Paint Hinge - Plain Bearing - Standard Weight Length of Joint : 3.5&quot; Width Open : 3.5&quot; Gauge of Metal : 0.123&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 1 pair Steel Paint Grade Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. Since these hinges are for temporary use and are standard template hinges, they are interchangeable with ball bearing hinges of the same size. FEATURES OF: STEEL PAINT GRADE HINGE - PLAIN BEARING - STANDARD WEIGHT HINGE BODY: Hinge body is manufactured from cold rolled mild steel. It is swaged to match the swage of our line of solid full mortise hinges. This allows the steel hinges to be removed and replaced with brass hinges after the completion of painting with no shimming or adjustment. FINISH: All hinges are finished in a durable beige prime coat. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. Both ends are threaded to accept the standard button finials or optional ball finials. FINIALS:Finials are threaded onto both ends of the pin and fit all steel mortise hinge sizes. Ball finials can be purchased separately in sets of four. Finials are individually packed, two per bag to facilitate sales of half pairs of hinges. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 3.5&quot; x 3.5&quot;Hinge - Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight - 13-3535/3 (SKU: KnobsandThings 37541)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight Length of Joint : 3.5&quot; Width Open : 3.5&quot; Gauge of Metal : 0.123&quot; Screw Size : 10 x 1.00&quot; Screw Quan. Per Pair: 12 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.0&quot; x 4.0&quot; Hinge - Solid Extrude Brass - Ball Bearing - Standard Weight - 11-4040BB (SKU: KnobsandThings 37555)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Ball Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 All 11 Series Hinges are Priced and Sold as Pairs. Equipped with two precision machined, anti-friction Stainless Steel ball bearing assemblies All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are threated into the barrel of the hinge to prevent the pin from rising. All hinges are interchangeable with our full mortise extrude hinges All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - BALL BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. BALL BEARINGS:Each hinge is equipped with two precision machined anti-friction Stainless Steel ball bearing assemblies. The two races are machined from 300 series Stainless Steel. The balls are made from through hardened Stainless Steel. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. These bearings greatly increase both the lateral and vertical load bearing capability of the hinge and therefore increase hinge life. They are recommended for doors which receive average frequency use. They are ALWAYS recommended for doors which are equipped with a door closer. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tappi


Von Morris Door Hardware 4.0&quot; x 4.0&quot; Hinge - Solid Extrude Brass - Plain Bearing - Standard Weight - 11-4040 (SKU: KnobsandThings 37557)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Plain Bearing - Standard weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 All 11 Series Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. #12 Machine Screws available for 11-4040 and 11-4545 upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.0&quot; x 4.0&quot; Hinge - Solid Extrude Brass - Two Knuckle - Ball Bearing - Standard Weight - 13-4040BB/ (SKU: KnobsandThings 37558)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Ball Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Hinge: 8 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches Equipped with one precision machined, anti-friction Stainless Steel ball bearing assembly. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material and are affixed to the bottom leaf. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - BALL BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction Stainless Steel ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are made from through hardened Stainless Steel. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. They are recommended for doors which receive average frequency use. They are ALWAYS recommended for doors which are equipped with a door closer. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter


Von Morris Door Hardware 4.0&quot; x 4.0&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-4040/2 (SKU: KnobsandThings 37560)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Hinge: 8 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL OR TWO KNUCKLE HINGE PIN COVER SELECTION


Von Morris Door Hardware 4.0&quot; x 4.0&quot; Hinge - Steel Paint Hinge - Plain Bearing - Standard Weight - 12-4040 (SKU: KnobsandThings 31030)
Von Morris Door Hardware Von Morris Steel Full Mortise Hinge Steel Paint Hinge - Plain Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 1 pair Steel Paint Grade Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. Since these hinges are for temporary use and are standard template hinges, they are interchangeable with ball bearing hinges of the same size. FEATURES OF: STEEL PAINT GRADE HINGE - PLAIN BEARING - STANDARD WEIGHT HINGE BODY: Hinge body is manufactured from cold rolled mild steel. It is swaged to match the swage of our line of solid full mortise hinges. This allows the steel hinges to be removed and replaced with brass hinges after the completion of painting with no shimming or adjustment. FINISH: All hinges are finished in a durable beige prime coat. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. Both ends are threaded to accept the standard button finials or optional ball finials. FINIALS:Finials are threaded onto both ends of the pin and fit all steel mortise hinge sizes. Ball finials can be purchased separately in sets of four. Finials are individually packed, two per bag to facilitate sales of half pairs of hinges. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.0&quot; x 4.0&quot;Hinge - Solid Extrude Brass - Three Knuckle - Ball Bearing - Standard Weight - 13-4040BB (SKU: KnobsandThings 33086)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Ball Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. Equipped with two precision machined, anti-friction Stainless Steel ball bearing assemblies. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All finials are interchangeable with our full mortise extruded hinges. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - BALL BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. BALL BEARINGS: Each hinge is equipped with two precision machined anti-friction Stainless Steel ball bearing assemblies. The two races are machined from 300 series Stainless Steel. The balls are made from through hardened Stainless Steel. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. These bearings greatly increase both the lateral and vertical load bearing capability of the hinge and therefore increase hinge life. They are recommended for doors which receive average frequency use. They are ALWAYS recommended for doors which are equipped with a door closer. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges ar


Von Morris Door Hardware 4.0&quot; x 4.0&quot;Hinge - Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight - 13-4040/3 (SKU: KnobsandThings 33219)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.5&quot; x 3.5&quot; Hinge - Paumelle - Heavy Weight - Solid Forged Brass - 18-4535 (SKU: KnobsandThings 36408)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Paumelle - Heavy Weight - Solid Forged Brass Length of Joint :4.5&quot; Width Open : 3.5&quot; Gauge of Metal : 0.203&quot; Screw Size : 14 x 1.50&quot; Screw Quan. Per Hinge: 8 Knuckle Size : 2.66&quot;H x 1.10&quot;D Paumelle Hinges are Priced and Sold as Eaches Equipped with two fully concealed, precision machined, anti-friction bearing assemblies per hinge, one Ball Thrust Bearing and one Needle Axial Bearing. Ball bearings are machined from 300 series Stainless Steel and employ Stainless Steel balls. All pins are precision machined from 300 series Stainless Steel. All Paumelle hinges are handed. Be sure to specify hand of hinge when ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: PAUMELLE - HEAVY WEIGHT - SOLID FORGED BRASS HINGES HINGE BODY: Hinge body is manufactured of solid forged brass. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are Stainless Steel as well. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 300 Stainless Steel for high durability and resistance to rust. They are permanently installed in one half of the hinge. The other end is rounded to facilitate re-assembly. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged eight per bag. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE


Von Morris Door Hardware 4.5&quot; x 4.5&quot; Hinge - Solid Extrude Brass - Ball Bearing - Standard Weight - 11-4545BB (SKU: KnobsandThings 36541)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Ball Bearing - Standard Weight Length of Joint : 4.5&quot; Width Open : 4.5&quot; Gauge of Metal : 0.134&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 All 11 Series Hinges are Priced and Sold as Pairs. Equipped with two precision machined, anti-friction Stainless Steel ball bearing assemblies All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are threated into the barrel of the hinge to prevent the pin from rising. All hinges are interchangeable with our full mortise extrude hinges All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - BALL BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. BALL BEARINGS:Each hinge is equipped with two precision machined anti-friction Stainless Steel ball bearing assemblies. The two races are machined from 300 series Stainless Steel. The balls are made from through hardened Stainless Steel. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. These bearings greatly increase both the lateral and vertical load bearing capability of the hinge and therefore increase hinge life. They are recommended for doors which receive average frequency use. They are ALWAYS recommended for doors which are equipped with a door closer. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tappi


Von Morris Door Hardware 4.5&quot; x 4.5&quot; Hinge - Solid Extrude Brass - Plain Bearing - Standard Weight - 11-4545 (SKU: KnobsandThings 37543)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Plain Bearing - Standard Weight Length of Joint : 4.5&quot; Width Open : 4.5&quot; Gauge of Metal : 0.134&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 All 11 Series Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. #12 Machine Screws available for 11-4040 and 11-4545 upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.5&quot; x 4.5&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-4545/2 (SKU: KnobsandThings 37538)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight Length of Joint : 4.5&quot; Width Open : 4.5&quot; Gauge of Metal : 0.134&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Hinge: 8 Two Knuckle Lift Off Hinges are Specified and Priced as Eaches All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of single hinges. #12 Machine Screws available upon request. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. ATTENTION: Custom Finishes Take 12 WEEKS To Deliver TO VIEW FINISHES, SEE COLORS AND FINISHES ABOVE SEE RELATED ITEMS FOR FINIAL OR TWO KNUCKLE HINGE PIN COVER SELECTION


Von Morris Door Hardware 4.5&quot; x 4.5&quot; Hinge - Solid Extrude Brass - Two Knuckle - Plain Bearing - Standard Weight - 13-4545/2 (SKU: KnobsandThings 37539)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Two Knuckle - Ball Bearing - Standard Weight Length of Joint : 4.5&quot; Width Open : 4.5&quot; Gauge of Metal : 0.134&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Hinge: 8 2 Hinges per box Two Knuckle Lift Off Hinges are Specified and Priced as Eaches Equipped with one precision machined, anti-friction Stainless Steel ball bearing assembly. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material and are affixed to the bottom leaf. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. All Two Knuckle Hinges are Handed. Be Sure to Specify Hand of Hinge When Ordering. SEE PRODUCT SPECIFICATIONS FOR HANDING DIAGRAM FEATURES OF: SOLID EXTRUDE BRASS -TWO KNUCKLE - BALL BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. BALL BEARINGS: Each hinge is equipped with one precision machined anti-friction Stainless Steel ball bearing assembly. The two races are machined from 300 series Stainless Steel. The balls are made from through hardened Stainless Steel. The bearing shell is machined from brass of the same alloy as the hinge body to ensure an accurate color match. The construction results in an extremely durable, long life ball bearing which is able to withstand years of hard use and corrosive environments. This bearing greatly increases both the lateral and vertical load bearing capability of the hinge and therefore increases hinge life. They are recommended for doors which receive average frequency use. They are ALWAYS recommended for doors which are equipped with a door closer. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. The exposed end is rounded to facilitate re-assembly, while the other end is permanently affixed to the bottom leaf. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of four. Decorative finials are individually bagged and sold in sets of four. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, fla


Von Morris Door Hardware 4.5&quot; x 4.5&quot; Hinge - Steel Paint Hinge - Plain Bearing - Standard Weight - 12-4545 (SKU: KnobsandThings 37540)
Von Morris Door Hardware Von Morris Steel Full Mortise Hinge Steel Paint Hinge - Plain Bearing - Standard Weight Length of Joint : 4.5&quot; Width Open : 4.5&quot; Gauge of Metal : 0.134&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 1 pair Steel Paint Grade Hinges are Priced and Sold as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. Since these hinges are for temporary use and are standard template hinges, they are interchangeable with ball bearing hinges of the same size. FEATURES OF: STEEL PAINT GRADE HINGE - PLAIN BEARING - STANDARD WEIGHT HINGE BODY: Hinge body is manufactured from cold rolled mild steel. It is swaged to match the swage of our line of solid full mortise hinges. This allows the steel hinges to be removed and replaced with brass hinges after the completion of painting with no shimming or adjustment. FINISH: All hinges are finished in a durable beige prime coat. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. Both ends are threaded to accept the standard button finials or optional ball finials. FINIALS:Finials are threaded onto both ends of the pin and fit all steel mortise hinge sizes. Ball finials can be purchased separately in sets of four. Finials are individually packed, two per bag to facilitate sales of half pairs of hinges. FASTENERS: All hinges are provided with type &quot;A&quot; tapping screws. These are solid brass, flat head, counter sunk, undercut phillips head screws. All screws are lacquered to prevent tarnishing. Screws are bagged either six per bag or eight per bag to facilitate sales of half pairs. NUMBER OF HINGES: For doors up to 89 inches, use three hinges. For each additional 30 inches or fraction thereof, use one additional hinge. SEE RELATED ITEMS FOR FINIAL SELECTION


Von Morris Door Hardware 4.5&quot; x 4.5&quot;Hinge - Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight - 13-4545/3 (SKU: KnobsandThings 37542)
Von Morris Door Hardware Von Morris Brass Full Mortise Hinge Solid Extrude Brass - Three Knuckle - Plain Bearing - Standard Weight Length of Joint : 4.0&quot; Width Open : 4.0&quot; Gauge of Metal : 0.130&quot; Screw Size : 12 x 1.25&quot; Screw Quan. Per Pair: 16 1 pair per box Three Knuckle Hinges are Specified and Priced as Pairs. All hinges have template screw hole locations for use with either wood or hollow metal doors and frames. All Pins are machined from high grade 304 Stainless Steel material. All Finials are Threated into the barrel of the hinge to prevent the pin from rising. All hinges are furnished standard with button finials and solid brass phillips head, type &quot;A&quot; tapping screws. FEATURES OF: SOLID EXTRUDE BRASS -THREE KNUCKLE - PLAIN BEARING - STANDARD WEIGHT HINGES HINGE BODY: Hinge body is manufactured from CDA alloy 38500 brass. It is machined from an extruded bar, resulting in a hinge with high strength and precision tolerances. The hinges are beveled at the barrel to provide a close fit when the hinge is both open and closed. FINISH: Hinges are individually hand polished assuring an even finish with no unpolished areas on the barrel. The lacquer is baked on catalyzed epoxy. Von Morris extruded hinges are supplied standard as clear coated, bright brass (605). Other finishes are available for an additional charge. Please refer to the Price List. PINS: Pins are machined from 304 Stainless Steel for high durability and resistance to rust. One end is rounded to facilitate re-assembly, while the other end is knurled to keep the pin from dropping through the hinge barrel during re-assembly. The pin is held in place by the threaded finials and can be easily removed by unthreading the finials and tapping the pin up from the bottom. FINIALS: Finials are threaded into both ends of the barrel and fit all full mortise hinge sizes. Finials can be purchased separately in sets of fou